The Canadian and More

I was looking after my son today, and after most of the morning was gone it was time to get out of the house. What to do on a beautiful, sunny day in Winnipeg? Go watch trains, of course!

I decided to go see the Canadian near CN Diamond just west of Winnipeg. We arrived just after noon, and I was surprised to see a westbound freight train (#347) stopped just west of the Perimeter highway. I guess they must have tripped the hotbox around mile 10. There was someone working on the rear of the train and they were chatting with the engine. I went up to the head end and took this shot at 12:20 just before they started to pull out.

CN 5722 and 2590 provided the power. Here's the video of them pulling out. I think I captured some pretty good engine sounds as they throttled up.


I heard on the scanner that VIA 1 had to back out of the station so they could take the south track. This made them a little late, and they finally showed up at 12:42. VIA 6451 and 6410 were providing a fair bit of smoke as they blew by us at a good clip.


The train had 6451 and 6410; baggage 8609; coaches 8100 and 8109; Skyline 8506; diner 8408 Empress; Skyline 8511; sleepers 8338 Rogers Manor, 8328 Grant Manor, 8342 Wolfe Manor, 8327 Fraser Manor, 8202 Chateau Bienville, 8217 Chateau Maisonneuve; Skyline 8505; diner 8409 Fairholme; sleepers 8326 Franklin Manor, 8329 Hearne Manor, and 8339 Sherwood Manor; and 8718 Yoho Park.

After that, we pulled up stakes and headed into town. I intended to go by BNSF to see if their rumoured new engine was there, but instead I saw a train heading west that made me turn around and chase it. I'll write about that next time!

CP 3106

On my way south on Kenaston Boulevard, I spotted a CP train switching just west of Kenaston. I stopped to take a few shots. CP 3106 was just finishing assembling a small train at 18:51. About 2 minutes later, they crossed Kenaston on their way north to St. James Junction and on to Rugby Yard.

CN 102 at St. James Junction

I saw CN 102 at St. James Junction around noon today, with IC 2707, CN 2662, and CN 5655 providing the power for a nice long train, all containers.

Scanners - Programming

Suppose you just purchased a scanner. What now? You have to program it. It's not difficult and it only takes an hour or so to get things set up right.

As I mentioned, I use a Uniden BC72XLT scanner. My comments on programming will reflect this, but I believe most scanners have a similar setup.

Scanners have a number of channels, which are each assigned a frequency to monitor. My Bearcat has 100 channels. Most scanners group these channels into "banks" to help you organize them. The Bearcat has 10 banks of 10 channels each. I have five banks set up: CN running, CN maintenance, CP running, CP maintenance, and end-of-train devices.

Programming the channels is pretty easy. You set the unit into programming mode, select the channel, and set the frequency. Simple as that!

The detail:
1. Press the Hold key.
2. Enter the channel number you want to program.
3. Press the Func key.
4. Press the E/Pgm key. Note the PGM in the top left of the display. The current frequency will be displayed, which should be 000.000 for an empty channel.
5. Type in the frequency, using the numbers and the period key.
6. Press the E key to finish.
7. You can then press E again to move to the next channel.
8. Repeat steps 5-7 as necessary.

It helps to have the channels all planned out before you start programming. That way, you can enter them one after the other.

On my Bearcat, it has "priority" channels (1 per bank) that get scanned more often than the other channels. You want to put the more interesting channels there. I have put the train channels for CN and CP in those slots, but I am thinking of changing it so the Winnipeg CN RTC is in the priority channel. I find myself listening to that channel more than any other.

The big problem with programming your scanner is: what frequencies should I monitor? That's the subject of the next post in the series.

Introduction to scanners

Run Eight

I had some time to kill this afternoon, so I ended up cruising around looking for trains. I happened to spot BCOL 4648 sitting cold by herself in Fort Rouge yard, so I stopped and took this shot.

Not much was going on, except that CN 401 and 102 were both getting ready to leave Symington Yard around 4 PM. I heard that 401 had a single engine, and was to pick up BCOL 4648 on their way west. I elected to leave the Symington area and wait for CN 401 at CN Subway off Osborne Street. While CN and CEMR crews were doing work in the yard, I waited for the train. Eventually 401 groaned into view at 16:24, with CN 5276 (an SD40-2W) pulling over 130 cars. She was really throbbing as she rolled by. Nice wave from the conductor! They came to a stop in the yard to hitch up to the Dash-9. When I left the area just after 17:00, the ex-BC Rail unit had not moved yet.

Scanners - An Introduction

Long-time readers will know that I highly recommend using a scanner when railfanning. In many cases it gives you a "heads up" that a train is coming, and in a few cases I have found a train that I would have otherwise missed.

What's a scanner? It is a radio receiver that you can program to scan certain frequencies. In my case I have it programmed to monitor railway frequencies that are used by CN and CP. The scanner rapidly loops through the channels (frequencies) you have programmed, looking for any kind of broadcast. If it finds one, it pauses there until the broadcast is complete, then it resumes scanning. You can also have it sit on one channel if there is a conversation there you want to monitor.

I use a Uniden BC72XLT scanner. It is a good basic hand-held scanner and it serves my purposes very well. The range is pretty good and it is easy to program and operate. You can't go too far wrong with Uniden.

I bought mine from Durham Radio in Ontario. You can also buy it on Amazon, or on eBay. Durham Radio is listing it for $129.95, Amazon says $77.76 with free shipping, and eBay averages around $80.

The only feature I wish it had was labels, so I could look at the scanner and have a description of the channel. It just shows the channel number. I printed out a little list of what the channels are, and taped it to the scanner so I can refer to it.

In my next post about scanners, I will talk about how to set up your scanner.

Friday Freight

I shot the BNSF transfer freight on Friday as it crossed Waverley Street on its way to CN's Fort Rouge yard. You may recall I saw the westbound version on September 9. I wanted to catch this version because I wanted to see the caboose leading the way.

I heard BNSF calling the CN RTC to get permission to enter the Rivers subdivision. While this was happening, a CP high-railer truck came north on the La Riviere subdivision and dismounted at Wilkes Avenue.


Once BNSF received permission to enter the mainline, I went to Waverley and waited by the side of the road for the transfer to come. Before too long the lights of the caboose became visible, the gates came down, and BN 12580 led four cars and BNSF 2743 past my lenses.





I didn't hang around for the return trip but I understand they had 2 cars to bring back.

Fredericton Train Station Refurbishment Details

The Fredericton train station will be refurbished, and leased out for 20 years to NB Liquor.

"The train station area will house a wine boutique and product sampling counter, with a food preparation area and room for specialty product displays," said Dana Clendenning, president and CEO of Alcool NB Liquor. The products, checkouts, cold room, warehouse and offices will be located in the new structure, and each will be open to the other."


The long freight shed on the rear of the station will be removed and a new, blocky building will be built to hold the main retail store. A parking lot will be built to the north of the station (where the old bottling depot was).

The artists rendering appears to be from the perspective of someone standing on York Street just north ("left") of the station.

The station will be connected to the existing trail system (finally). Work will commence shortly to prepare the station for the winter, and I imagine the first thing to go will be the roof. I'm told engineers were in the building today.

This is great news for the station, for Fredericton and for heritage people everywhere. Maybe the Heritage Canada Foundation can finally take the station off their 10 Most Endangered Places list!

NB Liquor announcement, CBC article, Charles Leblanc, Tim Scammell

CN 121

Dave and Matt went a-chasing trains recently on the Napadogan and Pelletier subdivisions in New Brunswick. Here are a few of their excellent videos.

They shot CN 121 at Ennishore first. This is Matt's video.


Next, Matt's view of CN 305 heading west over the massive Salmon River trestle near New Denmark, NB.


Here's Dave's view of CN 121 heading west on the Pelletier subdivision out of Edmundston, NB.

The Late Canadian Today

VIA's Canadian was a bit late today. BNSF Manitoba had enough time to zip over to Fort Rouge with 20 cars, pick up 10 cars, and return before VIA arrived on the scene at St. James Junction.



The complete consist:
Engines VIA 6427, 6404
Baggage VIA 8606
Coaches VIA 8106, 8119
Skyline VIA 8515
Diner VIA 8410 Frontenac
Skyline VIA 8502
Sleepers VIA 8340 Stuart Manor, VIA 8330 Hunter Manor, VIA 8314 Cameron Manor, VIA 8318 Craig Manor, VIA 8229 Chateau Viger, VIA 8212 Chateau Latour, VIA 8224 Chateau Roberval, VIA 8207 Chateau Dollard, VIA 8215 Chateau Lemoyne
Skyline VIA 8504
Diner VIA 8402 Alexandra
Sleepers VIA 8324 Dunsmuir Manor, VIA 8310 Brock Manor, VIA 8309 Brant Manor, VIA 8707 Kokanee Park

CP Units at the Scrapper Update

I took a quick look Wednesday afternoon at the CP units being scrapped in Winnipeg off Chevrier Boulevard. These are the units:

5753 and 5398 were actively being scrapped. 5398's prime mover was still aboard but 5753's was gone. By this evening, 5398's engine was gone too.

Next to be scrapped:
SOO 4203
SOO 4201
CP 1551
CP 1504
CP 1558
SOO 4202
SOO 4204
CP 1556

Fredericton Station Update

The station on June 28, 1978. Photo by Art Clowes.

There is a reception and press conference scheduled for Friday September 18 to discuss the details of the York Street train station refurbishment. I received my invitation, but it's a bit too much of a commute! The press conference starts at 10 AM at the Centennial Building on King Street in Fredericton.

Truck-Train Collision in Winnipeg Tuesday

A truck ran into a CEMR train on the Perimeter Highway just northeast of Winnipeg Tuesday around 4 PM. The Winnipeg Sun reported that a semi (transport truck to you Easterners) went around four stopped cars and plowed into the train as it was crossing the highway. The crossing lights were working but there are no barriers at that crossing. I doubt barriers would have made much difference in this situation.

CEMR 4000 was on the train, and from the Winnipeg Sun photos, it looks like the train struck the train between 4000 and the first freight car. It looks like there was some damage to 4000.

The driver was extricated from the cab and taken to hospital, and was reported to be in stable condition. The train crew was not injured.

The CEMR train was heading south on the Pine Falls subdivision. I had heard CEMR 4000 on the scanner on Monday around noon as they headed south on the Carman subdivision.

The Winnipeg Free Press and the CBC both had brief stories about the accident.

Three Oceans, One Weekend

David Morris sent along photos of the three Ocean trainsets from the last weekend in August. Too bad it was so rainy. The Moncton one is especially noteworthy because it features newly refurbished VIA 6402. Note the hump at the back of the engine for the new generator. This provides standby power to the train so they do not have to run the main engine at full power at the station.

2009/08/29 VIA 14, Sackville

6439-6419
7009
7220-7108-7208-7231
7311-7400-7313
7508-7522-7521-7526-7519-7524
7600
KOOTENAY

2009/08/29 VIA 15, Amherst

6406-6441
7011
7228-7230-7227
7312-7402-7308
7518-7517-7509-7501-7525-7512
7601
EVANGELINE

2009/08/30 VIA 14, Moncton

6400-6402
7003
7223-7226-7222-7217
7315-7401-7314
7500-7520-7507-7502-7506-7513
7602
REVELSTOKE

CP TEC Train on Great Sandhills Railway Tuesday

CP's TEC train in New Brunswick, July 29, 2008. Photo by David Morris.

The CP TEC (Track Evaluation C?) train will be running over the Great Sandhills Railway in Saskatchewan tomorrow (Tuesday September 15). It should leave Swift Current between 07:00 and 07:30 and proceed to Leader by mid afternoon, then on to Burstall to tie up for the night.

The Great Sandhills Railway operates on the former Burstall and Empress subdivisions.

Today's Late Canadian

VIA 1, the Canadian, was a bit late leaving Winnipeg today. They apparently had to make a stop at the VIA Maintenance Center to fix one car. I heard them switching on the scanner, and I was very curious what was going on. Another railfan stopped by and mentioned the reason for the delay.

In due time VIA 6410 and 6451 brought the 19 cars past.

The light was really nice today.

Here's YOHO PARK rolling over the diamond at St. James Junction.


The complete consist:
VIA 6410
VIA 6451
VIA 8609
VIA 8100
VIA 8109
VIA 8506 Skyline
VIA 8408 Empress
VIA 8511 Skyline
VIA 8338 Rogers Manor
VIA 8328 Grant Manor
VIA 8342 Wolfe Manor
VIA 8223 Chateau Rigaud
VIA 8325 Elgin Manor
VIA 8208 Chateau Dollier
VIA 8202 Chateau Bienville
VIA 8505 Skyline
VIA 8409 Fairholme
VIA 8326 Franklin Manor
VIA 8329 Hearne Manor
VIA 8339 Sherwood Manor
VIA 8718 Yoho Park

This is the seventh Canadian I have seen in Winnipeg since I moved here. Not bad! (Complete list)

CEMR 4012 and 4013

I mentioned that I saw CEMR 4013 at the CEMR shops a week ago. Geoff Sockett sent me a photo he took of CEMR 4013 and 4012 in Hantsport, Nova Scotia back on snowy January 16, 2006.

They were working the gypsum train at that time, I see.

CEMR's units 4011-4014 were built for CN as GP9s, numbered 4594, 4597, 4494 and 4567 respectively. They were rebuilt to GP9RM specifications with chopped noses and 1800 horsepower, and renumbered to 4011/4008/4013/4001.

CEMR sent 4011 through 4014 to the Windsor & Hantsport Railway in Nova Scotia in the summer of 2005. 4012 and 4014 came first, followed by 4011. 4013 was the last to arrive, in late August. They displaced the ex-CP MLW RS-23s that were working on the W&H.

4013 had a major failure on April 11, 2008 that wrecked the engine and main generator. 4012 was still operational in June 2008 but suffered a main generator failure soon afterward.

CEMR 4012 and 4013 left the Windsor & Hantsport Railway on March 5, 2009. They were in Dartmouth, Nova Scotia for a day or two, then arrived in Toronto on March 13. They finally arrived in Winnipeg on March 21. I do not know the present condition of the units.

Thanks for the photo, Geoff!

CN 2258 East

On my way back from the Prairie Dog Central, I caught CN 2258 East just before they were to pass under the Perimeter Highway on their way into Winnipeg at 15:30. CN 2621 was the second unit.

Shortly before that, I heard VIA 1 (the Canadian) announce they had a clear signal at Diamond (a few km west of this shot) at 15:20. That means the Canadian was about 3 hours late leaving Winnipeg!

Chance

New Brunswick, like most provinces, has a series of highway cameras set up around the province for people to view to see local conditions. Errol Robertson sent me this snap he took from the Welsford highway camera.

The regular eastbound freight was on time on September 9 at 13:12. Note slug 008 in second position. Good catch, Errol!

Steam Engine Maintenance

I volunteered today at the Prairie Dog Central railway. I had emailed earlier this week to say I was available, and I was asked to help wipe down their steam engine #3. I arrived this morning at 9 AM sharp and reported to their steam engine guru, Bob Harris.

My job, along with veteran Ziggy, was to wipe the engine down with varsol to clean it up. I put my coveralls, safety goggles and rubber gloves on, and got to work! The job basically consisted of wiping the engine with Varsol (a solvent), then doing a "dry wipe" with a cloth, then another wipe with Varsol and some oil to give it a shine. That's my pail and gloves on the engine in the photo above. I did the first wipe and some of the dry wiping, and Ziggy did the oil wipe. It took about four hours, and a lot of climbing, to get the job done but I think it looks a lot better now. The bell in particular was filthy, being just behind the stack. I also washed the windows in the cab.

After that, we did a water test to see the quality of water in the boiler. The intent of this is to see what additives, if any, need to be added to bring the water into specification. The water has to be pretty "basic" (opposite of acidic), not have too many dissolved solids, and have enough sulfides in it to absorb the oxygen in the water so it doesn't corrode the boiler system. There is so much to learn about steam engines!

We wrapped up around 2 PM. I decided to head out and take a few shots of the returning excursion train before heading home. I shot it three times before it reached Inkster Junction. Here's the video...


Thanks to everyone at PDC for showing me around. I look forward to volunteering again.

Fredericton Train Station To Be Restored

Big news... BIG news. NB Liquor makes tracks to station. Yes, the Fredericton train station is going to be restored, by the NB Liquor Corporation.

I confess that I had given up on the idea of the train station being restored. In my time as president of the Fredericton Friends of the Railway [Station] I championed the cause, but within the last year I had lost hope. I fully expected to read sometime in the next few years that the station was gone.

Maybe I should have moved out west sooner? ;)

You should follow Tim Scammell, former and current president of the FFoTR, for news on the station. And, of course, Charles Leblanc!

BNSF Transfer

I was at Sobeys on Grant Avenue yesterday at lunch and I noticed BNSF 2743 at the Fort Rouge Yard. I shot a quick video behind Sobeys as 2743, one freight car, and the caboose rolled west to their yard.

The area there is wide open but the sun is on the wrong side of the tracks. Too bad.

I think I am starting to understand their schedule. They head over to Fort Rouge around 11:30 to noon to interchange with CN. They usually wait for VIA to go by (either the Canadian or the Hudson Bay roll by just after noon) then return to their yard afterward.

On my way back I shot this photo of BNSF 2743 putting their one freight car away, just to get the engineer's side of the locomotive.

New Rail Line in Maine?

CBC news is reporting that the city of Eastport, Maine is applying for federal funding to rebuild a railway line from Eastport to the Canadian border at Calais.

The Maine Central Railway abandoned the Eastport branch line in 1978. I understand the state railbanked a portion of the old Calais branch, but the portion from Ayers Junction to Eastport was totally removed.

There is an engineering study posted on the Eastport Port Authority web site. Zipping to the bottom line, we find the costs estimated to be between $26 million and $44 million, depending on what level of track is deemed to be required.

All I can say is "good luck".

Subscribing to this blog

If you read this blog regularly and would like to receive a notice by email when I post, please click this link: subscribe to Confessions of a Train Geek by email.

If you use an RSS reader like Google Reader, then you can click on this icon to add the blog to your list.
Subscribe in a reader

Thanks for reading.

Slides for Sale

This shot was taken on this day, 11 years ago in 1998, by a David T. Stowe in Bathurst, NB.


I recently purchased a few slides from Tim Howerter. He has a large collection of original slides for sale. There are a variety of railways represented, including CN, CP, CSX, Norfolk Southern, Union Pacific and a large switcher collection. His prices are quite reasonable and so is the shipping.

I purchased about a dozen slides featuring MLW power on CP and CN.

Here is his sales listing from Railbid. His email address is dozermand6 a t rcn.com. (Replace a t with the @ sign)


Here is my updated list of original train slides for sale. The link below will take you directly to all of the folders with all slides for sale.

Directions on how to view:
- Either click on the link to go directly to my library of folders (if your computer allows this)
- Or copy and paste link into your URL address bar at the top of your home page.

To open folders: click on the folder. It will open with all the slides in that particular folder. Double click on the slide(so) you want to view and they will pop up in a much larger size for viewing. Continue onto each folder like this and take a look at everything I have. There is a very nice selection of locomotive rosters and action shots.

Link For Slides:
http://img.villagephotos.com/p/2008-7/1317892

There were many slides added to the switchers folders and others. Please take some time and view what I have for sale. All slides are originals, no duplicates. All slides were scanned at a low resolution, hence the fair quality of the scans. All slides have info, dates and location on slide mounts. The words you see on the scans do not appear on the slide itself. Email me back the folder name and the slides(file) numbers back to me of the ones you want to purchase.

Prices:
All action slides of trains are $1.50 each. All locomotive roster shots are $2.00 each

Shipping:
Slides are shipped First class mail and cost is $1.25 for the first 5 slides, $.50 for each additional 5 slides purchased.

I will accept cash, check or money order, or you may use paypal, but will have to pay the fee I am charged for accepting paypal payments which is 3%, + $.30 of total amount due(shipping costs included). I am sorry I have to charge this but if I do not this adds up to a large loss for me.

Hope to hear from you!
Thanks
Tim

Today's Hudson Bay, and One From Yesteryear

The northbound Hudson Bay was on time on a rainy day in Winnipeg today.
engines VIA 6458, 6413
baggage VIA 8601
coaches VIA 8113, VIA 8132
diner VIA 8418 York
sleeper VIA 8216 Chateau Levis

I stumbled across an extract from "Yet there isn't a train I wouldn't take": Railway Journeys by William D. Middleton that contains a description of the author's journey aboard the Hudson Bay in August 1998. You can read it here. The entire Hudson Bay article is present and can be read online. In 1998 the train had two FP9s for power, instead of the usual one or two F40PH-2s nowadays. The train itself was pretty much the same as it is today, with one baggage car, two coaches, diner ANNAPOLIS, and sleepers CHATEAU VIGER and HUNTER MANOR.

1919 Canadian National Railways Timetable Uploaded

Art Clowes provided a scan of the Canadian National Railways October 5, 1919 public timetable for me to upload to my web site.

Thanks, Art! link

Two Rebuilt Engines

David Chiasson posted a really nice video of Sunday's VIA 14 rolling over the Nepisiguit River. This had two rebuilt VIA engines on the head end, 6400 and 6402. You can tell 6402 is the second engine by the little hump on the back.

This is a great example of a great video. Well lit, good composition, great subject, and no 30 second lead-ins. Well done.

CN Test Train in the Maritimes

Various people on the AtlanticRails and RailsNB mailing lists have reported a CN test train in Nova Scotia and New Brunswick. CN 2517 and the two test cars, operating as train 482, worked the Dartmouth subdivision yesterday.

The test train, operating as train 912 today, went from Moncton down to Saint John and back.

Hopefully someone will get some good photos of old 2517 and the two blue test cars.

EDIT: here's a video from "John" aka cn8800!

Busy Day in Winnipeg, Part 2

Shortly after my last post, I spotted a westbound in the distance on the north track. Soon enough, CP 115 came rolling by at 17:00 with CP 8504 and 9810 on the head end, and CP 9783 midway through the train.

I kept an eye on the crossing arm after the train went by, and sure enough it was bouncing. The arm had gone up as normal, but it kept oscillating about 30 degrees from vertical back to vertical for about a minute. I called the CP number on the crossing to report it and they took the details down and said a maintainer would be dispatched.

With no more trains due to arrive for a while, we headed out. I drove around North Transcona for a bit and went up Risque Avenue (love that name) to the CEMR shops. I took a few shots through the fence. I saw CEMR GP9s 4010, 4013, 4001, 4002, ex-CP 5396 and snowplow CEMR 2.




We headed down south after that. Rolling past Symington Yard again revealed humpyard set CN 7511, CN 501, CN 504 and CN 7528 hard at work. I spotted a northbound train coming off the Sprague Subdivision but I was in no position to take a good photograph. The train had CN 2537, CN 5667, and CN 5661 for power.

That was a much better way to spend the afternoon than sitting at home!

Busy Day in Winnipeg

My wife was working today, so I was home with the kids. At about 3 PM it was obvious that I needed to get out of the house to preserve my sanity, so I bundled the kids into the van and took off for Slurpees and trains.

First we rolled up Fermor Avenue then Plessis Road past CN's Symington Yard. There wasn't much going on there. As I continued up Plessis Road I saw an eastbound freight rolling toward Symington Yard. I took a left onto Dugald Road, hoping to get to Symington's entrance before the train. Alas, the traffic lights were against me and I didn't quite make it. However, I did see that a westbound was waiting for the eastbound to get into the yard. I went up Warman Road to the end and waited for the train to pass. Once it passed at 16:00, CN 2261 and 2626 boomed a deep bass as the engineer throttled up for the long trip eastward.


The kids were clamoring for their Slurpees, so we hit a nearby 7-11 and took care of that. Then we headed north into CP territory. I randomly chose Day Street as a good place to watch the CP mainline action from, forgetting that it led right to the CEMR shops. Bonus! Within a few minutes of arriving there, a short eastbound rolled by at 16:44. The lead unit was CP 3014, but the nice surprise was the trailing unit, B unit CP 6078. I last saw this unit in Sintaluta, SK on June 25, 2009.


Right after the train passed, a black Suburban pulled up and a uniformed police officer beckoned me over. He asked if I had noticed if the crossing arm had bounced after the train went past, and I said I hadn't noticed. He said he had no problem with me being there, but not to walk the tracks. I of course agreed (safety first when railfanning!) and off he went. I should have checked to see if he was CP Police or Winnipeg Police. Doesn't matter, I wasn't doing anything wrong. :)

To be continued...

The Slug in Maine

A friend shot NB Southern's new slug 008 in Mattawamkeag, Maine on Saturday. He very kindly allowed me to post a few photos here. He got a really good shot of 008!

CP Units at the Scrapper Update

I had a good look Friday at the CP units being scrapped in Winnipeg off Chevrier Boulevard. These are the units:

5688 and 1593 were actively being scrapped. By Saturday they were pretty much gone.

In order of "next to be scrapped" on:

CP 5716
CP 5829
CP 5753
CP 5398
SOO 4203
SOO 4201
CP 1551
CP 1504
CP 1558
SOO 4202
SOO 4204
CP 1556

In the September 2009 Branchline, I read this note: "RETIRED UNITS SOLD: To Rail & Motor International (components to be salvaged and remains scrapped): CP Hump Comptroller 1151; GP9u 1561, 1593; SD40-2 5398; SD40M-2 5496; SD40-2 5679, 5688, 5701, 5716, 5753, 5829" I haven't seen some of those units yet but some are here now.

I was looking through my notes and I see I shot CP 5398 in Winnipeg back on October 11, 2005. In fact, I even blogged about it although I didn't put a photo of 5398 here. This is the best one I have, of 5398 and 5773 working the yard.


I see in that October 2005 blog post that I shot a northbound CP freight at the diamond at St. James Junction. The power for that CP freight? CP 3028 and 1128, exactly the same power I saw yesterday. Interesting.

CP 3028 South

I happened to catch CP 3028 and 1128 bring a southbound freight across the diamond at St. James Junction today in Winnipeg. Here's the video.

The Canadian Today, and more

Today's Canadian was very prompt, rolling into view at St. James Junction at 12:14. She had three-eyed VIA 6434 leading and 6408 trailing, both Spiderman-2 units.

They had 19 cars: baggage 8616; coaches 8118, 8104, and 8103; Skyline 8509; diner Louise; Skyline 8512, sleeper cars Drummond Manor, Dawson Manor, Cabot Manor, Blair Manor, Chateau Lasalle, and Chateau Salaberry; Skyline 8503; diner Emerald; sleepers Osler Manor, Laird Manor and Christie Manor; and Tremblant Park bringing up the markers.


Just after they passed, CN 303 was heard passing through Fort Rouge. There was some discussion about meeting CN 114 east of Diamond, as 303 apparently had a dimensional load and the rules say that either one of the two has to be stopped, or they both have to proceed at 10 MPH. I believe 114 ended up stopping.

CN 303 had Dash-9 2624 leading and IC 1009 trailing.

I think this was the dimensional load they were talking about, about six or so cars back from the engines.

It says "CB Energy Recovery" on it. It's a HSRG, a Heat Recovery Steam Generator. These are used to make steam from gas turbines or other waste heat sources.

CP on Sunday

First CN on Saturday, now CP on Sunday.

On my way back from the Prairie Dog Central, I stopped at Canadian Pacific Railway's Rigby Yard in downtown Winnipeg in the late afternoon. I went to the soccer field by the Diesel Repair Shops to see what was parked outside. Alas, a long container train (CP 110) was pulling slowly eastward and obstructed the view. CP 8741 was the lone unit up front, with CP 8624 in the middle and CP 8519 pushing on the rear. Here's 8624 going by:


As the end of the train neared, a little local with CP 5756 rolled by with 2 cars. Then 8519 came into view, then they all left and revealed CP 1693 patiently waiting in the rear. It turned out to be a neat little video.


I took a bunch of shots to take inventory of what was at the shops. These are what I saw:
CN 2513 (!)
CP 1128
CP 1576
CP 1617
CP 1636
CP 1695
CP 3028
CP 3081
CP 3122
CP 4657
CP 5733
CP 5868
CP 5909
CP 6042
CP 8275
CP 9728
SOO 6021

I didn't have time to go to the Arlington Bridge to see more of the yard. Next time!

Video of Dragon Boat Train

Kevin Gaudet posted a video featuring the NB Southern excursion train that ran to Renforth for the Dragon Boat festival this past Saturday. Lots of good horn action. Enjoy!

Volunteering at the Prairie Dog, Part 2

As I mentioned, I volunteered at the Prairie Dog Central Railway on Sunday.

I spent my time from Grosse Isle to Warren counting the money raised from the train robbery. We arrived at Warren, and steam engine #3 was cut off and run around the train.

I disembarked, and after using the port-a-potty I bought an ice cream and resumed my coin counting. There were a lot of coins! In the end I counted $273 raised. We left Warren and headed back toward Inkster Junction.


The return trip was pretty quick and we arrived at Inkster Junction just before 15:00. The passengers disembarked, and some went up into the steam engine. I wandered around taking a few photos.


The steam engine was eventually cut off, and diesel 4138 was fired up to put the coaches away for the night. A few of them were put on one shop track and the rest were put on the other. The caboose stays outside, apparently.


The steam engine was backed up to take on water.


Afterward, both the steam and diesel engines were run around to the south side of the shops.

I look forward to volunteering again. I would like to start as a porter, to be onboard the train and assist the passengers. Eventually I would like to join the head end crew as a brakeman, but that will take some time, and of course I will have to pass my rules course. So far so good!

CN Derailment in Moncton

Two CN locomotives derailed on the Point du Chene spur near Moncton late Sunday afternoon. CN 4762 and another unit (4143) hit a washout and the units rolled over. Fortunately the crew were not hurt. From the photo it does not look like they had any cars with them.

There was heavy rain in the Moncton area over the weekend, some 92 mm in places, and apparently the track was undermined on the spur. The Point du Chene spur serves the Scoudouc Industrial Park and used to go all the way to the wharf at Point du Chene.

Times & Transcript article


CN 4762 and 4725 in Gordon Yard in Moncton, April 11, 2009

EDIT: Added second unit number.